Français
Deutsch
Italiano
Русский
Español
Português
Nederlandse
Ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
Indonesia
Tiếng Việt
ไทย
বাংলা
فارسی
Polski
High Thermal Efficiency Two-layer Frame Plate Vulcanizing Machine - Used To Manufacture Rubber Fiberboard
High Thermal Efficiency Two-layer Frame Plate Vulcanizing Machine - Used To Manufacture Rubber Fiberboard
Machine introduction:
1. Types of rubber fiber sheet vulcanizers
(1) Flat vulcanizer (intermittent vulcanization)
Applicable products:
Ordinary rubber sheets (such as anti-slip mats, industrial rubber sheets)
Insulating rubber sheets (for distribution rooms)
Oil-resistant, acid-resistant and alkali-resistant rubber sheets
Conductive/antistatic rubber sheets
Composite rubber sheets with fiber reinforcement layers (such as asbestos rubber sheets, canvas-reinforced rubber sheets)
Working principle:
Put the mixed rubber sheet (or fiber-reinforced rubber composite material) into the mold.
High pressure (usually 10-20MPa) is applied through the hydraulic system, and the heating plate provides temperature (140-180℃).
Maintain a certain time (5-30 minutes, depending on the thickness) to complete the vulcanization.
Equipment features:
Can produce a wide range of thicknesses (1mm~50mm).
Suitable for small batch and multi-specification production.
Multi-layer vulcanization table can be added (to improve efficiency).
Technical Parameters
| Parameter | Typical Range | Explanation |
|---|---|---|
| Temperature | 140 - 180°C | For Natural Rubber (NR), it is usually 150 - 160°C. For EPDM, it can reach 170 - 180°C. |
| Pressure | 10 - 20MPa | To ensure the rubber flows adequately and eliminate air bubbles. |
| Vulcanization Time | 5 - 30 minutes | Depends on the thickness (e.g., for 5mm thickness, it takes about 10 - 15 minutes). |
| Cooling Method | Natural cooling / Water cooling | To prevent deformation and improve dimensional stability. |
3. Special requirements for fiber-reinforced rubber sheets
If the rubber sheet contains a fiber-reinforced layer (such as canvas, nylon, polyester fiber or asbestos fiber), pay attention to the following during vulcanization:
Fiber pretreatment: Glue or dip is required to improve adhesion with rubber.
Vulcanization pressure: Higher pressure (15-25MPa) is required to ensure that the rubber penetrates the fiber layer.
Temperature control: Avoid excessively high temperatures that may cause fiber aging (such as nylon fiber temperature resistance ≤180℃).
4. Common Problems and Solutions
| Problem | Possible Causes | Solutions |
| Bubbles/Layering | Insufficient pressure, poor venting | Increase pressure, add venting grooves to the mold |
| Uneven thickness | Uneven mold, poor fluidity of rubber compound | Adjust the parallelism of the mold, optimize the rubber compound formula |
| Delamination between fiber and rubber | Untreated fiber or insufficient adhesion |
Pre - coat fiber with adhesive, increase vulcanization pressure |
| Rough surface | Mold contamination, uneven temperature | Clean the mold, check the temperature uniformity of the heating plate |
Mr. Alexey Pan
General Manager
- Email: info@beishunchina.com
- Tel: +86 15154222850
- WhatsApp: 8615154222850
-
WeChat:
Beishunrubbermachine
-
Flat Rubber Vulcanizing Press Machine Electric Heating Or Steam Heating
Flat rubber vulcanizing press adopts electric heating or steam heating Features: The small flat vulcanizer produced by Qingdao Beishun is a kind of equipment used for molding and vulcanization of rubber products. It is widely used in laboratory research, product development and small batch ... -
PLC Automatic Mold Opening Rubber Vulcanizing Machine / Insulating Rubber Pad Making Machine
PLC Automatic Mold Opening Rubber Vulcanizing Machine / Insulating Rubber Pad Making Machine A rubber insulation pad vulcanizing machine is specialized equipment used to manufacture rubber insulation pads through the vulcanization process. Vulcanization involves heating raw rubber with sulfur or ... -
75L Rubber Kneader Mixer Banbury Kneader Dispersion Kneader Machine
PLC Control X(S)N-75 Rubber Dispersion Kneader Machine Banbury Pressed Kneader Applications The pressurized rubber kneader machine is engineered for use in rubber and rubber product factories. According to the structure, the kneader can be divided into a pressurized kneader and an open kneader. ...
